Schmid Watson Specifications Page 30
- Page / 130
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Watson TDM
Operating Manual
Watson-TDM-Manual-W.doc
Version 2.0-01
3-8
Revision: 2008-02-07
External Clock Mode
Tabletop
Modem
Plug-in
Modem
DSL
Tx
Rx
Rx
Tx
E1E1
External Clock
2048 kHz
Figure 3-5: External Clock Mode
In external clock mode, the 2048kHz input clock is fed directly in the plug-in from
the clock input of the minirack mechanics or via the ACU clock input. The exter-
nal clock is used as the E1 reference clock.
If no external clock is present at the 2048kHz clock input, the E1 transmit clock is
used as the clock source. If no signal is received at the E1 Port, then the internal
clock is used as the clock source.
If the external clock option is disabled, the primary E1 clock source is the 2Mbit/s
transmit clock. If no signal is received at the E1 Port, then the internal clock is
used as the clock source.
The external clock is never used to drive the E1 Rx direction.
3.2.5 High Capacity E1
Watson TDM plug-in modems with E1 interfaces can be configured to
G.SHDSL.bis linerates and transport more than one E1 over a DSL span. High
Capacity E1 is activated with LTUMODEs 14, 15 and 16:
LTUMODE 14
E1 Port #1
E1 Port #2
E1 Port #3
E1 Port #4
DSL Port A
4 Mbps
DSL Port C
4 Mbps
Note: DSL Ports B, D are unused
Figure 3-6: LTUMODE 14
- Declaration of Conformity 3
- Revision: 2008-02-07 iii 5
- Revision: 2008-02-07 v 7
- Revision: 2008-02-07 vii 9
- Limited Product Warranty 11
- Table of Contents 13
- Revision: 2008-02-07 xiii 15
- Revision: 2008-02-07 xv 17
- 1 References 19
- 2 Watson TDM Overview 20
- 2.3 Accessories 21
- 3 Watson TDM Features 23
- 3.1.3 Multipair operation 24
- Revision: 2008-02-07 3-3 25
- 3.1.5 Power Backoff 26
- 3.2 E1 Interface 27
- 3.2.2 AIS Detection 28
- 3.2.3 AIS Generation 28
- 3.2.4 E1 Clock Modes 29
- 3.2.5 High Capacity E1 30
- LTUMODE 15 31
- Note: DSL Port C is unused 31
- LTUMODE 16 31
- Note: DSL Port D is unused 31
- 3.3 ISDN PRA Interface 32
- Revision: 2008-02-07 3-11 33
- Revision: 2008-02-07 3-13 35
- 3.4 nx64 kbit/s Interface 37
- 3.4.2 Handshake Operation 38
- 3.4.5 Clock Direction 39
- 3.4.6 Clock Polarity 39
- 3.4.7 Byte Timing 39
- 3.5 Timeslot Mapping 40
- 3.5.2 nx64 mappings 41
- DSLSTU-C STU-R 42
- 3.6.1 Introduction 43
- 3.6.2 Configuration 44
- 3.6.4 Multipoint Cascading 48
- 3.7 Performance Monitoring 50
- Revision: 2008-02-07 3-29 51
- 3.8 Test loops 52
- Normal Operation 53
- After Automatic Protection 53
- Switching 53
- 3.10 Password Protection 54
- 4 Watson TDM Regenerator 55
- 4.3 Cascading 56
- 4.4 Powering 56
- Revision: 2008-02-07 4-3 57
- 5 Powering 59
- 5.3 Remote Powering 60
- 5.3.4 Power Failure Alarm 61
- Loopfeedfeed 62
- 6 LEDs, Alarms 63
- 6.2 Tabletop LEDs 64
- 6.3 Alarm Conditions 65
- 6.4 Alarm Relays 66
- 6.5 Initialization Errors 66
- 7 The Monitor 67
- 7.2 Addressing 68
- 7.2.3 Tabletop 69
- 7.3 The Monitor 70
- 7.3.4 Shortcuts 71
- 7.3.5 Continuous Displays 71
- 8.1 Introduction 73
- 8.2.1 General Commands 74
- Revision: 2008-02-07 8-5 77
- 8.2.3 DSL Configuration 79
- 8.2.5 E1 Configuration 82
- 8.2.6 PRA Configuration 82
- Revision: 2008-02-07 8-11 83
- Current Status 90
- Switched Line 90
- Command 91
- ≥ 30% on channel x (A 92
- 8.3.4 Loops 95
- 8.3.5 Reset Commands 96
- 8.4.1 G.826 Statistics 97
- 8.5.1 Connection control 101
- 8.5.2 Inventory 101
- 8.5.3 Password Commands 102
- 9 Connectors 104
- Watson-TDM-Manual-W.doc 105
- Version 2.0-01 105
- Watson TDM 105
- Operating Manual 105
- Revision: 2008-02-07 9-33 105
- 9.1.2 Tabletop Modems 106
- 9.2 DSL Connector 107
- 9.3 E1 Connectors 108
- 9.3.3 75 Ohm Connectors 109
- 9.4 nx64 kbit/s Connector 110
- Revision: 2008-02-07 9-39 111
- 9.5 Monitor Connector 112
- 9.6.2 Ground connector 113
- 9.7 Regenerator Connector 114
- 10 Cables and Mechanics 115
- 10.1.2 Tabletop 116
- 10.2 Cable Reference 117
- 10.2.3 V.35 DTE Cable 119
- 10.2.4 V.35 DCE Cable 120
- 10.2.5 X.21 DTE Cable 121
- 10.2.6 X.21 DCE Cable 121
- 11.1 Interfaces 123
- 11.1.2 User Interfaces 124
- 11.1.3 Monitor Interface 124
- 11.2 Internal clock 125
- 11.4 Power Consumption 125
- 11.5 MTBF Values 126
- 11.6 Environment 127
- 12 Product Order Codes 128
- 12.3 Regenerator 129
- 12.4 Accessories 129
- 12.5 Cables 130
© 2020, manymanuals.com. All rights reserved. | 2.703 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals