Schmid Watson Specifications Page 95
- Page / 134
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Watson-Ethernet-Manual.doc
Version 3.3-01
Watson Ethernet
Operating Manual
Revision: 2010-01-20
7-33
7.3.5 Test loops
LOOP1 Ethernet-Port ON timeout | OFF
The LOOP1 command controls the local loopback, cf. chapter 3.6:
The loop is automatically cleared after the timeout specified in the command (5
minutes in the example above). If no timeout value is specified then the loop will
stay active until it is deactivated by a LOOP1 OFF command.
LOOP2 Span ON timeout | OFF
The LOOP2 controls the remote loopback on a DSL span.
The loop is automatically cleared after the timeout specified in the command (5
minutes in the example above). If no timeout value is specified then the loop will
stay active until it is deactivated by a LOOP2 OFF command.
In case of remote Loop 2 requests, the master has higher priority that the slave.
Notes:
On the Watson Ethernet tabletop modems it is not possible to specify an
Ethernet port or a DSL span. LOOP1 loops the Ethernet port, LOOP2 the
DSL span at the remote side..
On the Watson Ethernet tabletop modems a loop timeout is not supported
The LOOP2 command is not available on the Watson Ethernet tabletop
modem if it is configured as DSL slave
Looped-back Ethernet packets egress the modems from the same port they
were sent to and have the same source and destination addresses they
were sent with. While Ethernet testing equipment can handle this situation it
might be very confusing for "normal" Ethernet ports or Ethernet switches.
7.3.6 Reset Commands
RESET
Typing RESET on the Watson Ethernet tabletop resets the modem.
RESET Span
Typing RESET Span on the Watson Ethernet plug-in restarts a DSL span:
RESETCARD
The RESETCARD command initiates a complete hardware and software reset of
the Watson Ethernet plug-in. The RESETCARD command must be confirmed be-
fore it is processed.
Note:
This command is not available on the Watson Ethernet tabletop modem.
- Declaration of Conformity 3
- Limited Product Warranty 9
- Table of Contents 11
- 1 Related Documents 17
- 2 Overview 19
- 3 Modem Features 23
- 3.1.2 Multipair operation 24
- 3.1.4 Power Backoff 26
- 3.1.7 Wetting Current 28
- 3.1.8 Master / Slave 29
- 3.1.9 DSL Clocking 29
- 3.2.1 Ethernet over DSL 29
- 3.2.2 Ethernet Bridging 30
- 3.2.4 VLANs 31
- 3.2.5 VLAN Examples 31
- 3.2.7 Stacked VLANs 35
- 3.3.1 Ethernet over DSL 41
- 3.3.2 VLAN features 41
- 3.3.4 Cisco HDLC 42
- 3.4 Firmware update 43
- 3.5 Management 43
- DISCONNECT 45
- 3.7 Test loops 48
- 3.8 Password protection 49
- 4 Powering 51
- 5 LEDs and Alarms 53
- 5.2 Tabletop LEDs 54
- 5.3 Alarm Conditions 55
- 5.4 Alarm Relays 55
- 5.5 Initialization Errors 56
- 6 The Monitor 57
- 6.2 Addressing of Plug-ins 58
- 6.3 Naming of ports 59
- 6.4 Telnet Access 59
- 6.5.1 Welcome Screen 60
- 6.5.2 Menus 60
- 6.5.4 Tab completion 61
- 6.5.5 Help 61
- 6.5.6 Command History 61
- 6.5.7 Continuous Displays 62
- 7.1 Introduction 63
- 7.2.1 General Commands 64
- DEFAULT Configuration 66
- 7.3.1 Diagnostic 89
- 7.3.2 Status (Plug-in) 90
- 7.3.3 Status (Tabletop) 92
- 7.3.4 Alarms 93
- 7.3.5 Test loops 95
- 7.3.6 Reset Commands 95
- 7.4.1 G.826 Statistics 96
- 7.4.2 Ethernet Statistics 97
- 7.5.1 Connection control 100
- 7.5.2 Inventory 100
- 7.5.3 Password 101
- 7.5.4 Firmware Update 103
- 8 SNMP 105
- ENTITIY-MIB 106
- 8.1.3 SNMP Configuration 107
- 8.1.4 The Entity MIB 107
- 8.1.6 The ifTable 109
- 8.2 MIB Reference 110
- 8.2.5 RMON (RFC 2819) 111
- 8.2.6 IF MIB (RFC 2863) 111
- 8.2.11 MAU MIB (RFC 3636) 112
- 8.2.15 HDSL MIB 114
- 8.2.16 Schmid MIB 115
- 8.2.17 Watson MIB 115
- 9 Front and Rear Panels 117
- 10 Connectors and Cables 119
- 10.2 DSL Interface 121
- 10.2.2 DSL Cable 122
- 10.3 Ethernet Interface 123
- 10.4 Monitor Interface 123
- 10.5 Power and Grounding 124
- 11.1 Interfaces 127
- 11.2 Power Consumption 128
- 11.3 Ethernet 128
- 11.5 Management Functions 129
- 11.6 MTBF 129
- 11.7 Environment 130
- 12 Terminology 131
- 13 Product Order Codes 133
- Revision: 2010-01-20 134
Related products and manuals for Networking Schmid Watson
Networking Schmid Watson Technical Information
(292 pages)
(292 pages)
Networking Schmid Watson Specifications
(103 pages)
(103 pages)
Networking Schmid Watson Installation Guide
(129 pages)
(129 pages)
Networking Schmid Watson Specifications
(130 pages)
(130 pages)
© 2020, manymanuals.com. All rights reserved. | 0.322 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals