Schmid Watson Specifications Page 101
- Page / 134
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Watson-Ethernet-Manual.doc
Version 3.3-01
Watson Ethernet
Operating Manual
Revision: 2010-01-20
7-39
7.5.3 Password
CHANGE PASSWORD
The CHANGE PASSWORD command is used to change a password. The old
password has to be known to change it. The new password must be entered
twice to confirm it.
NTU_SM> CHANGE PASSWORD
Old password: ******
New password: ******
Confirm new password: ******
52:11:40 new password set
CLEAR PASSWORD
The CLEAR PASSWORD command clears the currently set password and disables
password protection. This is the factory default setting.
NTU_SM> CLEAR PASSWORD
Old password: ******
Password cleared and Monitor protection disabled
DSLSLAVE
The DSLSLAVE command is the only command allowed while password protec-
tion is active. The DSLSLAVE command is used to configure a master tabletop as
a DSL slave to allow a remote terminal access in case the password of a master
tabletop has to be changed or cleared.
Monitor Password Protection
Enter password: ******** (typed DSLSLAVE)
Device is now DSL slave
Note:
Through the remote terminal, i.e. through the DSL EOC the password commands
are available without password protection. If a modem has been password pro-
tected and the password has been lost then it can be cleared again from modem
configured as DSL master. If the modem who's password has been lost is confi-
gured as DSL master it can be set to DSL slave with the DSLSLAVE command
that is available even while password protection is active.
LOGOFF
LOGOFF activates the password protected mode. The previously set password
has to be entered before any new Monitor commands can be issued via the local
terminal.
SET PASSWORD
The SET PASSWORD command allows definition of a password on the tabletop.
Once a password is set the modem will go into a protected mode either after the
command LOGOFF is issued, after a timeout of 5 minutes or after a restart.
- Declaration of Conformity 3
- Limited Product Warranty 9
- Table of Contents 11
- 1 Related Documents 17
- 2 Overview 19
- 3 Modem Features 23
- 3.1.2 Multipair operation 24
- 3.1.4 Power Backoff 26
- 3.1.7 Wetting Current 28
- 3.1.8 Master / Slave 29
- 3.1.9 DSL Clocking 29
- 3.2.1 Ethernet over DSL 29
- 3.2.2 Ethernet Bridging 30
- 3.2.4 VLANs 31
- 3.2.5 VLAN Examples 31
- 3.2.7 Stacked VLANs 35
- 3.3.1 Ethernet over DSL 41
- 3.3.2 VLAN features 41
- 3.3.4 Cisco HDLC 42
- 3.4 Firmware update 43
- 3.5 Management 43
- DISCONNECT 45
- 3.7 Test loops 48
- 3.8 Password protection 49
- 4 Powering 51
- 5 LEDs and Alarms 53
- 5.2 Tabletop LEDs 54
- 5.3 Alarm Conditions 55
- 5.4 Alarm Relays 55
- 5.5 Initialization Errors 56
- 6 The Monitor 57
- 6.2 Addressing of Plug-ins 58
- 6.3 Naming of ports 59
- 6.4 Telnet Access 59
- 6.5.1 Welcome Screen 60
- 6.5.2 Menus 60
- 6.5.4 Tab completion 61
- 6.5.5 Help 61
- 6.5.6 Command History 61
- 6.5.7 Continuous Displays 62
- 7.1 Introduction 63
- 7.2.1 General Commands 64
- DEFAULT Configuration 66
- 7.3.1 Diagnostic 89
- 7.3.2 Status (Plug-in) 90
- 7.3.3 Status (Tabletop) 92
- 7.3.4 Alarms 93
- 7.3.5 Test loops 95
- 7.3.6 Reset Commands 95
- 7.4.1 G.826 Statistics 96
- 7.4.2 Ethernet Statistics 97
- 7.5.1 Connection control 100
- 7.5.2 Inventory 100
- 7.5.3 Password 101
- 7.5.4 Firmware Update 103
- 8 SNMP 105
- ENTITIY-MIB 106
- 8.1.3 SNMP Configuration 107
- 8.1.4 The Entity MIB 107
- 8.1.6 The ifTable 109
- 8.2 MIB Reference 110
- 8.2.5 RMON (RFC 2819) 111
- 8.2.6 IF MIB (RFC 2863) 111
- 8.2.11 MAU MIB (RFC 3636) 112
- 8.2.15 HDSL MIB 114
- 8.2.16 Schmid MIB 115
- 8.2.17 Watson MIB 115
- 9 Front and Rear Panels 117
- 10 Connectors and Cables 119
- 10.2 DSL Interface 121
- 10.2.2 DSL Cable 122
- 10.3 Ethernet Interface 123
- 10.4 Monitor Interface 123
- 10.5 Power and Grounding 124
- 11.1 Interfaces 127
- 11.2 Power Consumption 128
- 11.3 Ethernet 128
- 11.5 Management Functions 129
- 11.6 MTBF 129
- 11.7 Environment 130
- 12 Terminology 131
- 13 Product Order Codes 133
- Revision: 2010-01-20 134
Related products and manuals for Networking Schmid Watson
Networking Schmid Watson Technical Information
(292 pages)
(292 pages)
Networking Schmid Watson Specifications
(103 pages)
(103 pages)
Networking Schmid Watson Installation Guide
(129 pages)
(129 pages)
Networking Schmid Watson Specifications
(130 pages)
(130 pages)
© 2020, manymanuals.com. All rights reserved. | 0.449 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals